| 產品參數 | |||
|---|---|---|---|
| 品牌 | 力士樂 | ||
| 控制方式 | 系統 | ||
| 是否進口 | 進口 | ||
| 是否支持加工定制 | 支持 | ||
| 保質期 | 6個月 | ||
| 產品型號 | DKC02.3-100-7-FW | ||
| USB接口數量 | 6 | ||
| 畫面 | 高清 | ||
| 顏色 | 灰色 | ||
| 可售賣地 | 北京;天津;河北;山西;內蒙古;遼寧;吉林;黑龍江;上海;江蘇;浙江;安徽;福建;江西;山東;河南;湖北;湖南;廣東;廣西;海南;重慶;四川;貴州;云南;西藏;陜西;甘肅;青海;寧夏;新疆 | ||
| 用途 | 車間使用 | ||
F630 Negative Travel Limit Value is Exceeded超過負行程限值
.jpg)
The drive has been provided with a command value that leads to an axis
b outside the negative travel range.
為驅動器提供了一個指向軸的命令值位置在負行程范圍之外。
The axis has been stopped and the error reb "set velocity command value to zero" issued. Bit 2 of P-0-0090,
軸已停止，并發出錯誤反應“將速度命令值設置為零”。P-0-0090的鉆頭2，
Travel limit beter has been set to "Exceeding the travel limit is an error", or a drive control command has been started while the axis limit value is exceeded (e.g. drive-controlled homing).行程限制參數已設置為“超過行程限制是一個錯誤”，或者在超過軸限制值時啟動了驅動控制命令（例如，驅動控制歸位）。
Cause:原因：
S-0-0050, Negative b limit value is exceeded.
S-0-0050，超過負位置限值。
Remedial b:補救措施：
1. Check S-0-0050, Negative b limit value
檢查S-0-0050，負位置限值
2. Check the controller software limits
檢查控制器軟件限制
3. Activate the axis after the error reb
錯誤反應后激活軸
Procedure:
Clear the error Activate power if it has been de-activated
Move the axis to the permissible working range
清除錯誤。如果電源已停用，則激活電源將軸移動到允許的工作范圍
Note:Only command values that lead back into the permissible working range will be accepted. Any other command value will stop the drive again.
注意：只有返回允許工作范圍的命令值才會被接受。任何其他命令值都將再次停止驅動器。
