2.5，利用書本先走一遍書本，查看以上各個環節書本是否輸送順暢，書本間距，毛刷位置，切刀位置是否正確合理。
2.5 Use books to go over books again, see the above b whether the smooth delivery of books, books, spacing, brush b, cutter b is correct and reasonable.
2.6，架上包背條卷料。調好中心位置，倒入膠水在膠水盆里，讓膠水覆蓋上膠輪一半以上位置，調好膠水厚薄調節螺母，用手拉動包背紙，穿過電眼下軸，送料輪，上膠輪定位軸，上膠下壓軸，轉向軸，發熱棒，前面定位軸，使其始終居中為好。
2.6 Rack on the package back material. Adjust the center b, pour the glue in the glue basin, let glue cover the rubber wheel more than half of the b, adjust the glue thickness adjustment nut, hand pull package back paper, through the electric eye axis, feed wheel, rubber wheel bing Axis, on the glue under the finale, steering shaft, heating rods, in front of the bing axis, it is always centered as well.
2.7，手動狀態下按下觸摸屏手動頁面的上膠水按鈕（如圖），包背紙一頭用手拉上前定位軸，慢慢點動開關至?xí)景齿喗M第一個輪，繼續點動，讓包背紙接觸到書本同步一起走到最后一個包背輪。然后繼續點動完成一本至后面出書為止。查看包背紙松緊度與平行度。直到切換到自動狀態下開機運行完成。
2.7 Manual mode, press the manual button on the touch screen manual on the glue (Figure), the package back a hand pull the front bing shaft, slowly switch to the book bag the first round of the back wheel set, continue to jog, let The package backing paper comes into contact with the book synchronization and goes to the last package back wheel. And then continue to complete a jog to the back of a book so far. Check the backpack tension and parallelism. Until the switch to the automatic state to complete the boot operation.
臺歷自動鎖線機 鐵絲訂書設備維護與保養
3. Maintenance
3.1臺歷自動鎖線機 鐵絲訂書設備每一個星期加注一次包背輪轉軸位置黃油一次，讓其轉動自如
3.1 Once a week to add a packet back-wheel shaft b butter once, let it rotate freely
3.2，臺歷自動鎖線機 鐵絲訂書設備工作運行30天左右加注一次機器內部傳動齒輪黃油和傳動鏈條機油一次，讓其工作順暢，減少摩擦與磨損。
3.2 Work about 30 days to add a machine internal transmission gear butter and the transmission chain oil once, let the work smoothly, reduce friction and wear.
3.3，臺歷自動鎖線機 鐵絲訂書設備每次停機長時間不使用務必清理干凈膠盆與涂膠輪上的膠水，交接班的情況下可以在控制界面上設置手動頁面把膠水輪打開，讓其轉動，防止膠水固化，松開一點刮刀間歇，減少摩擦。
3.3 Each time the machine is not used for a long time to be sure to clean up the glue and glue on the glue wheel, the shift in case you can set the manual interface to open the glue wheel, let the rotation to prevent glue curing, Intermittent, reduce friction.
山東省
濟南市 青島市 臨沂市 濟寧市 菏澤市 煙臺市 泰安市 淄博市 濰坊市 日照市 威海市 濱州市 東營市 聊城市 德州市 萊蕪市 棗莊市
臺歷自動鎖線機 鐵絲訂書設備