PA66 A3WG5德國巴斯夫華韻塑料供應商
7 尼龍的優點
1.機械強度高，韌性好，有較高的抗拉、抗壓強度。比拉伸強度高于金屬，比壓縮強度與金屬不相上下，但它的剛性不及金屬。抗拉強度接近于屈服強度，比ABS高一倍多。對沖擊、應力振動的吸收能力強，沖擊強度比一般塑料高了許多，并優于縮醛樹脂。
巴斯夫PA66型號系列：
華韻塑膠PA66玻璃纖維增強25% 德國巴斯夫Ultramid A3WG5
華韻塑膠PA66玻璃纖維增強25% 德國巴斯夫Ultramid A3K
華韻塑膠PA66玻璃纖維增強25% 德國巴斯夫Ultramid A3Z
華韻塑膠PA66玻璃纖維增強25% 德國巴斯夫Ultramid A3EG3
朗盛PA66型號系列：
華韻塑膠PA66玻璃纖維增強25% 德國朗盛 A30S
華韻塑膠PA66玻璃纖維增強25% 德國朗盛 AKV15H1.
華韻塑膠PA66玻璃纖維增強25% 德國朗盛 AKV30H2.
華韻塑膠PA66玻璃纖維增強25% 德國朗盛 AKV35H1.
首諾PA66型號系列：
華韻塑膠PA66玻璃纖維增強25% 美國首諾 R533H
華韻塑膠PA66玻璃纖維增強25% 美國首諾 R543H
華韻塑膠PA66玻璃纖維增強25% 美國首諾 21SPC
華韻塑膠PA66玻璃纖維增強25% 美國首諾 M344 BK
PA應用
2.耐疲勞性能突出，制件經多次反復屈折仍能保持原有機械強度。常見的自動扶梯扶手、新型的自行車塑料輪圈周期性疲勞作用極明顯的場合經常應用PA。
3.軟化點高，耐熱(如尼龍46等,高結晶性尼龍的熱變形溫度高,可在150度下長期使用.PA66經過玻璃纖維增強以后,其熱變形溫度達到250度以上)。
4. Smooth surface, small friction coefficient, wear resistance. As a mobile mechanical components, self-lubricating, low noise, in the friction is not too high can not add lubricants to use; if really need to use lubricants to reduce friction or help heat dissipation, water, oil, grease, etc. Can be selected. Thus, as a transmission component, its service life is long. 5. Corrosion resistant, very resistant to Alkali and most salt liquids, also resistant to weak acids, motor oils, gasoline, aromatic compounds and solvents in general, inert to aromaticity, but not resistant to strong acids and oxidants. It can resist the erosion of gasoline, oil, fat, alcohol, Weak Alkali and has good anti-aging ability. It can be used as packing material for lubricating oil, fuel, etc. . 6. Self-extinguishing, non-toxic, odorless, good weather resistance, inert to biological erosion, with good antibacterial, anti-mildew ability. Kill. Excellent electrical perbance. Good electrical insulation, Nylon volume resistance is very high, high breakdown voltage, in dry environment, can be used as power frequency insulation materials, even in high humidity environment still has good electrical insulation. 8. The parts are light in weight, easy to stain and shape. Because of the lower melt viscosity, it can flow quickly. Easy to mold filling, high freezing point after mold filling, can quickly shape, so the bing cycle is short, high production efficiency.
